Nabíjecí kabely & adaptéry

OptiMate Solar + 80W Solar Panel6-step 12V 6.67A sealed solar battery-saving charger & trickle chargerCHARGERescues empty batteries from just 1 volt thanks to its unique pulse action. The fastest way of charging – thanks to the ‘smart charge’ control that chooses pulse charging or continuous charging depending on the strength of the sunlight. Intelligent maintenance – continues the next day if the battery held the charge overnight; if not, the programme moves on to the OPTIMISE step.MONITORBattery status is shown every 3 seconds. Notification that the battery is ready for STD and high-performance AGM batteries. Consumes less than 0.5mA during monitor mode. Automatically switches to CHARGE when there is sufficient solar energy.MOUNTINGThe OptiMate charge controller is separate from the panel and can be placed close to the vehicle or the battery, so that the charging progress and the maintenance of the battery can easily be monitored. The solar panel must be mounted so that it receives direct sunlight. The range/distance between battery and panel is 315 cm/124?. Use the OptiMate extension cables O-03, O-13 or O-23 to connect the solar panel to the OptiMate charge controller over a longer distance.External dimensions, including corner mounting brackets: Width = 68.5 cm / 27” Height = 77.2 cm / 30.4? Depth = 3.3 cm / 1 1/4“Solar panel:POWER: 80 watt (max.)VOLT: 12V nominal, 22V maximum.USE: Outdoor / indoor.STYLE: Weatherproof, aluminium frame with 4 mounting brackets, output cable 200 cm / 80? with SAE connector. OptiMate charge monitor:CHARGE AMPS: 6.67A from 80W panel (max. average current), 3-5A pulse current.USE: Indoor / outdoor (lowest temperature: -4°F / -20°C).RECOVERY: starts from a low voltage of 1VIDEAL FOR: STD, AGM and GEL 12V batteries between 2-240Ah.INPUT: 15 – 22VSTYLE: Weatherproof charge controller case.INCLUDED: Weatherproof battery cable and standard set of battery clamps included & 80W solar panelSAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected.WARRANTY: 3-year limited replacement warranty.

With this adapter from OptiMate you can easily reverse the polarity of your SAE 2-pin connector on your standard solar panel or the wiring of your vehicle accessory.Use this adapter to convert any industry-standard SAE 2-pin connector to fit your OptiMate. It contains 2 weatherproof SAE rubber seals and has been tested to industry-standard durability. Built to last, then! It is also ideal for use in the toughest environments. Even at a low temperature of -40°C/-40°F it stays flexible!Specifications:- Length: 6 inch/15 cm- SAE 2-pin connector to industry standard- Maximum current: 10 A- Suitable for use at very low temperatures down to -40 °C/-40 °F, cable stays flexible at temperatures down to “below freezing”.- Includes built-in rubber seal for OptiMATE heavy-duty SAE connector- High-quality cable designed by TecMate- 3-year limited warranty

Set of measuring pins with a unique slotted shape for connection to the end of cables of an electrical system. The slotted shape prevents damage to seals. • Supplied as standard with IgnitionMate (1 set) and IgnitionMate DUO (2 sets). • Small and large slotted shape for connection pins of various sizes. • Works with electrical test connector of 4 mm diameter. • 2-year limited warranty. High-quality accessory for TecMate diagnostic equipment.

Socket box - SAE to DC2.5Length: 30cm / 12?Suitable for use at very low temperatures down to -40 °C/-40 °F, cable remains flexible at temperatures down to “below freezing”.

Socket - SAE - weatherproof - panel mountLength = 100 cm / 40?Front-panel mounting, fastening at the rear, for panels with a thickness of 1 mm / 0.040? or more.Standard 2-pole SAE connectorMax. cable capacity: 5 AmpUse at very low temperatures -40°C/-40°F; stays flexible at temperatures below freezing.

Socket - SAE - weatherproof - panel mountLength = 15 cm / 6?Front-panel mount, connection at the rear, for panels with a thickness of 1 mm / 0,040? or more.Standard 2-pin SAE connectorMax. cable capacity: 5 AmpUse at very low temperatures -40°C/-40°F; remains flexible at temperatures below freezing.

TITAN+ is a complete and professional multifunctional instrument suitable for charging and starting all 12V and 24V electrical systems in vehicles, trucks, and small, medium and large vehicles. It is a powerful, reliable device controlled by a microprocessor and designed to carry out automatic charging cycles specific to standard wet batteries and a new Gel/AGM battery of up to 10 charging and analysis phases. Thanks to the new ECS (Electronic Control System) technology, the TITAN + series combines excellent reliability with fast charging and maintenance at higher power.Specifications:- Voltage: 12 - 24V- Charging current: 1 - 70A (1 - 100A eff)- Starting current: 650PA, 450CA- Charging capacity: 4 - 700Ah- Weight: 28kg- 3 programmed charging cycles + 1 manual cycle- Electronic potentiometer for current adjustment- Electronic control system- Charging cycle in 10 phases- Removal of sulphate deposits + recovery- Constant analysis- Supply function- Dual voltage 12/24V- Integrated electronic protection- Ideal for Start&Stop + Spiral batteries- Compatible batteries: PB, WET, GEL, AGM, SPIRAL, MF, VRLA

TITAN+ is a complete and professional multifunctional instrument suitable for charging and starting all 12V and 24V electrical systems in vehicles, trucks, and small, medium and large vehicles. It is a powerful, reliable device controlled by a microprocessor and designed to carry out automatic charging cycles, specific to standard wet batteries and a new Gel/AGM battery of up to 10 charging and analysis phases. Thanks to the new ECS (Electronic Control System) technology, the TITAN + series combines excellent reliability with fast charging and maintenance at higher power.Specifications:- Voltage: 12 - 24V- Charging current: 1 - 40A (1 - 60A eff)- Starting current: 350PA, 250CA- Charging capacity: 4 - 450Ah- Weight: 18kg- 3 programmed charging cycles + 1 manual cycle- Electronic potentiometer for current adjustment- Electronic control system- Charging cycle in 10 phases- Removal of sulphate deposits + recovery- Constant analysis- Supply function- Integrated electronic protection- Ideal for Start&Stop + Spiral batteries- Compatible batteries: PB, WET, GEL, AGM, SPIRAL, MF, VRLA

This trickle charger has a microprocessor that ensures the connected battery is automatically monitored and charged. In addition, the battery charger is protected against short circuits and reverse polarity.Specifications:• Voltage: 12V• Charging current: 4A• Charging capacity: 7ah - 100ah• Maintenance capacity: 7ah - 160ah• Microprocessor with 8-step charging process• Compatible batteries: WET, AGM, GEL, MF, Start & Stop• Dimensions: 190x110x60mm• Energy-efficient• Certification: CE• LED charge status indication• Mounting hook• Protective bumperMicroprocessor functions:• Reverse polarity protection• Short-circuit protection• Packaging: Box + charger + battery clamps + ring adapter

automatic charger 12v/1.5-10aInput: 230V AC ~ 50HzOutput: 1.5 / 10A 12VBattery charging range capacity (1.5 MODE): 2.3AH - 30AH Battery charging range capacity (10 MODE): 30AH - 200AH - 200AH Battery charging range CCA: 10CCA - 1000CCA Minimum starting voltage: 2VDimensions: 210 mm x 98 mm x 60 mm x 60 mmWeight: 0.88 kgBattery technology selection function (AGM , AGM , AGM SPIRAL , AGM , SLI , EFB , CALCIUM , VRLA , GEL BATTERIES , LITHIUM INCLUDING LIFEPO4 ).Reverse polarity protectionOver-temperature protectionShort-circuit protectionSpark-free protectionIngress protection rating: IP65

OptiMate 2 DUO, the powerful “no brainer” battery charger-maintainer for the hi-tech battery in all your vehicles – Guarantees healthy lithium or lead-acid batteries!CHARGE VOLTAGE: Nominal: 12V & 12.8V range: 4V – 14.4VOPERATION: Fully automaticSTEPS: 5INPUT: Global (100-240V 50-60Hz), high efficiency (CEC listed).STYLE: Weatherproof housing with wall mount, with 6ft / 180cm AC power cable and 6ft / 180cm charge cable with SAE connection at the end.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Suppresses sparks. Safe for long-term battery maintenance. Automatic shutdown in the event of a short circuit or disconnection of the battery.INCLUDED: Water-resistant battery charger and battery clip setWARRANTY: 3-year limited replacement warranty.Ideal for 12V lead-acid and 12.8V / 13.2V lithium LFP (LiFePO4) batteries.Delivers a constant 2 Amp charge current recommended for maintaining larger batteries.Charges and provides long-term maintenance – Connect to the battery and the OptiMate 2 DUO does the rest, no supervision required!More features:Automatically adapts to Pb or LFP battery. Safe to stay connected. Full electronic protection.Keeps the battery at full charge & good health.Starts from a low voltage of 4V.Warns when battery damage is detected.Energy-saving technologyv Stand-by power less than 0.5W.v Efficient 24-7 battery maintenance.Weatherproof. Suitable for use down to -40°C / -40°F.

The most TRUSTED battery charger in racing! The OptiMate 3, the all-in-one tool for maintaining your 12V battery at home. Diagnosis, recovery, charging, tests and optimal maintenance are carried out automatically. This latest version of the OptiMate 3 offers all the user-friendly features of the more than two million OptiMates produced since 1995, but is now lighter and more efficient than ever. The OptiMate 3 desulfates batteries and then tests them after charging. The maintenance program delivers only what the battery needs, without ever overcharging or undercharging it.CHARGING CURRENT: 0,8 A (constant current)USE: Indoor/outdoor (lowest temperature: -4 °F/-20 °C).RECOVERY: Starts from a low voltage of 2 V and two-phase desulfation recovery.IDEAL FOR: 12 V STD, AGM and GEL batteries between 3 – 50 AhINPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC-listed), fully sealed.DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable and standard set with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

OptiMate 3 x 4 - 12V 0.8A7-step 12 V 0,8 A battery-saving charger, tester and maintainer with 4 banks The most TRUSTED battery charger in racing in a 4-bank version. The OptiMate 3 x 4, the all-in-one tool for maintaining 4 12V batteries at home, in the garage or in the vehicle storage facility. Diagnosis, recovery, charging, tests and optimal maintenance are carried out automatically. The OptiMate 3 x 4 offers all the user-friendly features of the more than two million OptiMates produced since 1995, but is now lighter and more efficient than ever, and maintains 4 batteries simultaneously and independently of each other. The OptiMate 3 x 4 desulfates batteries and then tests them after charging. The maintenance program delivers only what the battery needs, without ever overcharging or undercharging it. • CHARGING CURRENT: 0,8 A (constant current, per bank)• USE: Indoor/outdoor (lowest temperature: -4 °F/-20 °C).• RECOVERY: Starts from a low voltage of 2 V and two-phase desulfation recovery.• IDEAL FOR: 4 pieces 12 V STD, AGM and GEL battery between 3 – 50 Ah• INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC-listed), fully sealed.• DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and 4 charging cables of 6 ft/180 cm ending in an SAE connector. 4 weatherproof battery cables and 4 standard sets with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year replacement warranty.

The OptiMate 4 Quad Program provides the ultimate maintenance for the high-tech 12V battery of the motorcycle, side-car and jet ski. This trickle charger tests the condition of the battery both before and after charging.The charger recovers batteries that are flat down to 0.5V. The recovery charger is compatible for charging with a 12V socket and with BMW canbus-controlled sockets. It is suitable for all 12V powersport batteries, including lead-acid, AGM & GEL and Li-Ion with LFP LifePO4 technology.Specifications:• Charge voltage: 12V - 12.8V• Charge current: 1.25A• Charge range: 0.5V - 14.4V• Minimum temperature: -40°CCharge process: 9 steps• Low voltage start• Protection - Activate• Battery test before charging• Recover sulphated battery• Pulsing to monitor cells• Charging• Optimising the final charge• Battery test after charging• Maintenance 24/7Safety features:• Safe for electronics• Suppresses sparks• Automatic shutdown in the event of a short circuit or disconnection

Ideal 12V battery maintenance for START/STOP & deep cycle applications. The OptiMate 5 recovers batteries from as low as 2 V and then provides charging and maintenance, all automatically. Perfect for months of maintenance of 12 V lead-acid batteries of any size and from 15 Ah to 192 Ah – deep cycle batteries, car batteries (also for EFB batteries – start/stop systems), leisure craft, motorcycles, …CHARGING CURRENT: 4 A (constant current, with temperature compensation)USE: Indoor/outdoor (lowest temperature: -4 °F/-20 °C).RECOVERY: Starts from a low voltage of 2 V and single-phase desulfation recovery.IDEAL FOR: 12 V EFB, STD, AGM and GEL batteries between 15 – 192 AhINPUT CURRENT: Universal (100-240 V 50-60 Hz), fully sealed.DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable and standard set with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

Advanced maintenance for 6V and 12V batteries of race cars/cars/watercraft. The OptiMate 5 VoltMatic can RECOVER and CHARGE all 6V and 12V lead-acid batteries. Connect the charger to the battery and the VoltMatic microprocessor automatically selects the correct voltage for charging a 6V battery in any state or a healthy* 12V battery and proceeds to charge. * Switching to manual operation is available for 12V batteries with very low voltage.;Charge current is controlled by the size and status of the connected battery.;Leave connected for months of unattended maintenance charging; the OptiMate detects the battery status and delivers charge when needed, to keep the battery 100% charged.•CHARGE CURRENT: 4 A (6 V) / 2.8 A (12 V) (Ampmatic)•USE: Indoor/outdoor (lowest temperature: -20 °C).•RECOVERY: Starts from a low voltage of 1 V and two-stage desulphation recovery.•IDEAL FOR: STD, AGM and GEL 6 V and 12 V batteries between 8 – 120 Ah (up to 192 Ah for 6 V).•INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC listed), fully sealed.•DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 180 cm charge cable with SAE connector as end. Weatherproof battery cable and standard set of battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected.3-year limited replacement warranty.

The world’s most advanced fully automatic 12V battery charger! The OptiMate 6 recovers batteries that other chargers can no longer save, because the OptiMate 6 sees the difference between an empty battery that needs charging and a fully discharged sulphated battery that needs recovering. Perfect for months of maintenance of any 12V lead-acid battery, such as deep-cycle batteries, batteries for cars, pleasure craft, motorcycles, … Multi-stage desulphation: Recovers neglected batteries from 0.5 voltAmpmatic charge control: adjusts the current to each battery size (3 to 240 Ah) OR battery status for the fastest and most complete chargeCell voltage balance mode: correctly prepares NEW batteries for first use and optimises battery performanceDaily battery status tests and interactive trickle charging: keeps the battery fully charged for weeks or months.•CHARGE CURRENT: 6 A (Ampmatic)•USE: Indoor/outdoor (lowest temperature: -40 °F/-40 °C).•RECOVERY: Starts from a low voltage of 0.5 V and two-stage desulphation recovery.•IDEAL FOR: STD, AGM and GEL 12 V batteries between 3 – 240 Ah•INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC listed), fully sealed.•DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charge cable with SAE connector as end. Weatherproof battery cable and standard set of battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.Ampmatic explained:

The world’s most advanced battery charger for starter & deep-cycle 12V batteriesOptiMate 6 Select is perfect for 12 V start and deep-cycle batteries that require precise temperature-controlled charging and long-term unattended maintenance. When selecting the voltage (14.4 V / 14.7 V), a safety check is performed to ensure the battery is charged at the correct voltage. Special feature: POWER SUPPLY delivers stable power for reprogramming a vehicle system, demonstrating a showroom model or retaining stored settings when battery cables are disconnected to connect powered accessories or to replace the batteryCHARGE CURRENT : 6A (Ampmatic) @ 14.4V / 14.7V / 4A@ 13.6VUSE: Indoor / Outdoor (lowest temperature: -40°F / -40°C).RECOVERY : Starts from a low voltage of 0.5V + 2-stage desulphation recovery.IDEAL FOR: STD, AGM, GEL & Deep Cycle 12V batteries from 3 – 240Ah.INPUT CURRENT: Universal (100-240V 50-60Hz), high efficiency (CEC approved), fully sealed.DESIGN : Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charge cable with SAE connector as end. Weatherproof battery cable and standard set of battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

The most advanced 12V 10A & 24V 5A battery charger in the world!OptiMate 7 12V-24V is perfect for high-performance 12V and 24V starter and deep cycle batteries that require precise temperature-controlled charging and long-term maintenance without supervision.SPECIAL FEATURES: Designed for sensitive electronics: The SAVE program is designed for SAFE and fully automatic low-voltage start (from 0.5 volts) and PULSE recovery of deeply discharged batteries connected to very sensitive electronics such as light aircraft or industrial equipment.Protection against incorrect voltage selection: When 24 V is selected and a 12 V battery is connected, OptiMate 7 12-24 V will immediately warn that a low voltage is detected. Charging will not start. The USER must confirm that the nominal voltage of the connected battery is 24 V before the SAVE mode is activated.CHARGING CURRENT: 10A @ 12V / 5A @ 24V (Ampmatic)USE: Indoor/outdoor (lowest temperature: -40 °F/-40 °C).RECOVERY: Starts from a low voltage of 0.5 V (12 V) and single-phase desulfation recovery.IDEAL FOR: 12 V (3 – 400 Ah) / 24 V (1-200Ah) STD, AGM and GEL batteries.NOW ALSO SUITABLE FOR CALCIUM CALCIUM BATTERIES! special 15 volt charging program INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC-listed), fully sealed.DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable and standard set with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

The world’s most advanced 10 A battery charger for start and deep-cycle batteries!OptiMate 7 Select is perfect for 12 V start and deep-cycle batteries that require precise temperature-controlled charging and long-term unattended maintenance. When selecting the voltage (14.4 V / 14.7 V), a safety check is performed to ensure the battery is charged at the correct voltage. Special feature: POWER SUPPLY delivers stable power for reprogramming a vehicle system, demonstrating a showroom model or retaining stored settings when battery cables are disconnected to connect powered accessories or to replace the batteryCHARGE CURRENT: 10A (Ampmatic) @ 14.4V / 14.7V / 8A @ 13.6VUSE: Indoor / Outdoor (lowest temperature: -40°F / -40°C).RECOVERY: Starts from a low voltage of 0.5V + 2-stage desulphation recovery.IDEAL FOR: STD, AGM, GEL & Deep Cycle 12V batteries from 3 – 240Ah.INPUT CURRENT: Universal (100-240V 50-60Hz), high efficiency (CEC approved), fully sealed.DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charge cable with SAE connector as end. Weatherproof battery cable and standard set of battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

CHARGE YOUR 12V – 13.2V BATTERY VIA ANOTHER 12V BATTERY! NO MAINS POWER NEEDED. Ideal for both lead-acid and LFP (LiFePO4) batteries.Charge the battery of your towed motorcycle, quad or speedboat while you are on the road.OptiMATE DC-to-DC draws power from your own vehicle's battery or an external 12V battery to recover, charge and maintain another 12V – 13.2V battery.The highly efficient long-term maintenance mode of the OptiMATE DC-to-DC protects the source battery and only draws power when the battery to be charged needs power. The OptiMATE maintenance mode keeps the battery fully charged, prevents overcharging, extends the service life and improves the battery's performance.OptiMATE DC-to-DC can recover a heavily discharged sulfated battery of even 2 volts.CHARGING AMPS: 2AUSE: indoor / outdoor (lowest temperature: -4 °F / -20 °C).RECOVERY: starts from a low voltage of 2VIDEAL FOR: 12V STD, AGM and GEL batteries and Lithium batteries between 3-96 Ah.INPUT: 12-16 V, 2,7 A maxSTYLE: weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable, standard set with battery clamps and fused battery clamp set included.SAFE: no risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

The OptiMate PRO-4 DUO is an automatic diagnostic battery charger for 4x 12V lead-acid batteries and/or 12.8V LiFePO4 batteries (Lithium Iron Phosphate). This trickle charger offers a choice of 3 functions: charge mode for 12 V lead-acid, charge mode for 12.8 V LiFePO4 or a shortened programme with a limited charge time of 60 minutes. It is suitable for first-time charging/activation of a new battery or a quick recharge of a healthy used battery with a voltage of 11.4V or higher. Specifications:- Input: 100-240 V, 50-60 HZ- Output: 12V, 5A- CE certification- Class 2 AC cable, O-43 extension cable 180cm and O-14 fused battery clamps included- IP40Use:- Select the correct charge mode for deeply discharged Pb/lead-acid batteries or LFP/LiFePO4 batteries or LFP/LiFePO4 batteries that require a BMS reset.

The SPI1 battery charger has a maximum charging current of 1 amp. The charger works on 230V AC and charges 6V and 12V DC batteries. Thanks to the hook, the charger is easy to store during charging, so that the cables are not in the way. In addition, this trickle charger is fitted with a rubber housing to protect it even better against impact and drop damage.Specifications:• Voltage: 6V DC - 12V DC• Min. battery voltage: 0,5V• Max. charging current: 1A• Suitable for: AGM, GEL, CALCIUM, Start 'n Stop• Rubber housing• Microprocessor• Protection against reverse polarity• Thermal protection• Automatic shut-off• Hook• IP54

The SPI10 battery charger has a maximum charging current of 10 amperes. The charger runs on 230V AC and charges 12V DC batteries. Thanks to the hook, the charger is easy to store while charging, so the cables don't get in the way. In addition, this trickle charger has a rubber housing to protect it even better against impact and drop damage. Specifications: • Voltage: 12V DC • Min. battery voltage: 0,5V • Max. charging current: 10A • Suitable for: AGM, GEL, CALCIUM, Start 'n Stop • Rubber housing • Microprocessor • Protection against reverse polarity • Thermal protection • Automatic shut-off • Hook • IP20