Nabíjecí kabely & adaptéry

Advanced maintenance for 6V and 12V batteries of race cars/cars/watercraft. The OptiMate 5 VoltMatic can RECOVER and CHARGE all 6V and 12V lead-acid batteries. Connect the charger to the battery and the VoltMatic microprocessor automatically selects the correct voltage for charging a 6V battery in any state or a healthy* 12V battery and proceeds to charge. * Switching to manual operation is available for 12V batteries with very low voltage.;Charge current is controlled by the size and status of the connected battery.;Leave connected for months of unattended maintenance charging; the OptiMate detects the battery status and delivers charge when needed, to keep the battery 100% charged.•CHARGE CURRENT: 4 A (6 V) / 2.8 A (12 V) (Ampmatic)•USE: Indoor/outdoor (lowest temperature: -20 °C).•RECOVERY: Starts from a low voltage of 1 V and two-stage desulphation recovery.•IDEAL FOR: STD, AGM and GEL 6 V and 12 V batteries between 8 – 120 Ah (up to 192 Ah for 6 V).•INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC listed), fully sealed.•DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 180 cm charge cable with SAE connector as end. Weatherproof battery cable and standard set of battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected.3-year limited replacement warranty.

Y-splitter - SAE to 2x fused SAEDistribute the power from your permanent battery cable, create 2 SAE outputs.•Length=12 inch/ 30 cm•SAE 2-pin connector to industry standard•Maximum cable current: 5 Amp•Suitable for use at low temperatures down to -20 °C/-4 °F•Includes built-in rubber seal and sealing cap for OptiMATE heavy-duty SAE connector.High-quality cable designed by TecMate. 3-year limited warranty.

The OptiMate 4 Quad Program provides the ultimate maintenance for the high-tech 12V battery of the motorcycle, side-car and jet ski. This trickle charger tests the condition of the battery both before and after charging.The charger recovers batteries that are flat down to 0.5V. The recovery charger is compatible for charging with a 12V socket and with BMW canbus-controlled sockets. It is suitable for all 12V powersport batteries, including lead-acid, AGM & GEL and Li-Ion with LFP LifePO4 technology.Specifications:• Charge voltage: 12V - 12.8V• Charge current: 1.25A• Charge range: 0.5V - 14.4V• Minimum temperature: -40°CCharge process: 9 steps• Low voltage start• Protection - Activate• Battery test before charging• Recover sulphated battery• Pulsing to monitor cells• Charging• Optimising the final charge• Battery test after charging• Maintenance 24/7Safety features:• Safe for electronics• Suppresses sparks• Automatic shutdown in the event of a short circuit or disconnection

OptiMate Solar DUO + 20W Solar Panel6-step 12V / 12.8V 1.67A sealed solar battery-saving charger & trickle chargerCHARGERescues empty batteries from just 4 volt thanks to its unique pulse action. The fastest way of charging – thanks to the ‘smart charge’ control that chooses pulse charging or continuous charging depending on the strength of the sunlight. Intelligent maintenance – continues the next day if the battery held the charge overnight; if not, the programme moves on to the OPTIMISE step.MONITORBattery status is shown every 3 seconds. Notification that the battery is ready for STD and hi-performance AGM batteries and Lithium LFP batteries. Consumes less than 0.5mA during monitor mode. Automatically switches to CHARGE when there is sufficient solar energy.MOUNTINGThe OptiMate charge controller is separate from the panel and can be placed close to the vehicle or the battery, so that the charging progress and the maintenance of the battery can easily be monitored. The solar panel must be mounted so that it receives direct sunlight. The range/distance between battery and panel is 315 cm/124?. Use the OptiMate extension cables O-03, O-13 or O-23 to connect the solar panel to the OptiMate charge controller over a longer distance.External dimensions, including corner mounting brackets: Width= 36.2 cm / 14.3” Height= 45.5 cm / 17.9” Depth= 2.6 cm / 1Solar panel:POWER : 20 Watts (max.)VOLTS : 12V / 12.8VUSE : Outdoor.STYLE : Weatherproof – polycrystalline, aluminium frame with 4 mounting brackets, output cable 200 cm / 80? with SAE connector. OptiMate charge monitor:CHARGE AMPS : 1.67A from 20W panel (max. average current), 3-5A pulse currentUSE : Indoor / outdoor (lowest temperature: -4 °F / -20 °C).RECOVERY : starts from a low voltage of 4VIDEAL FOR : STD, AGM and GEL 12V batteries from 2 – 240Ah and lithium LFP batteries of 12.8V/13.2VINPUT : 15 – 22VSTYLE : Weatherproof charge monitor housing.INCLUDED: INCLUDED: Weatherproof battery cable, standard battery clamp set, 20W solar panelSAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected.WARRANTY: 3-year limited replacement warranty.

OptiMate Solar + 80W Solar Panel6-step 12V 6.67A sealed solar battery-saving charger & trickle chargerCHARGERescues empty batteries from just 1 volt thanks to its unique pulse action. The fastest way of charging – thanks to the ‘smart charge’ control that chooses pulse charging or continuous charging depending on the strength of the sunlight. Intelligent maintenance – continues the next day if the battery held the charge overnight; if not, the programme moves on to the OPTIMISE step.MONITORBattery status is shown every 3 seconds. Notification that the battery is ready for STD and high-performance AGM batteries. Consumes less than 0.5mA during monitor mode. Automatically switches to CHARGE when there is sufficient solar energy.MOUNTINGThe OptiMate charge controller is separate from the panel and can be placed close to the vehicle or the battery, so that the charging progress and the maintenance of the battery can easily be monitored. The solar panel must be mounted so that it receives direct sunlight. The range/distance between battery and panel is 315 cm/124?. Use the OptiMate extension cables O-03, O-13 or O-23 to connect the solar panel to the OptiMate charge controller over a longer distance.External dimensions, including corner mounting brackets: Width = 68.5 cm / 27” Height = 77.2 cm / 30.4? Depth = 3.3 cm / 1 1/4“Solar panel:POWER: 80 watt (max.)VOLT: 12V nominal, 22V maximum.USE: Outdoor / indoor.STYLE: Weatherproof, aluminium frame with 4 mounting brackets, output cable 200 cm / 80? with SAE connector. OptiMate charge monitor:CHARGE AMPS: 6.67A from 80W panel (max. average current), 3-5A pulse current.USE: Indoor / outdoor (lowest temperature: -4°F / -20°C).RECOVERY: starts from a low voltage of 1VIDEAL FOR: STD, AGM and GEL 12V batteries between 2-240Ah.INPUT: 15 – 22VSTYLE: Weatherproof charge controller case.INCLUDED: Weatherproof battery cable and standard set of battery clamps included & 80W solar panelSAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shutdown in the event of a short circuit or when the battery is disconnected.WARRANTY: 3-year limited replacement warranty.

Extension cable for adapter, SAE to MOTOR contact 180° - 120cmCable:18AWG 0.82MMConnector 1:SAEConnector 2:BIKE (DIN Z 12MM) PLUG, STRAIGHTLength:4FT / 120CMStarts temperature:-40°F / -40°C

The OptiMate MagCode provides a fast, safe and easy battery charger connection. Attach the magnet to its counterpart on the battery and (re)charge without using clamps. This magnet must be attached to the battery charger via the SAE connector. This quick connection is suitable for indoor and outdoor use (down to -40°C).Specifications:• Magnetic charging connector• MagCode system• Cable protection• Voltage: 24V• Cable length: 75cm• SAE charging connector• Operating temperature: down to -40°C

The most advanced 12V 10A & 24V 5A battery charger in the world!OptiMate 7 12V-24V is perfect for high-performance 12V and 24V starter and deep cycle batteries that require precise temperature-controlled charging and long-term maintenance without supervision.SPECIAL FEATURES: Designed for sensitive electronics: The SAVE program is designed for SAFE and fully automatic low-voltage start (from 0.5 volts) and PULSE recovery of deeply discharged batteries connected to very sensitive electronics such as light aircraft or industrial equipment.Protection against incorrect voltage selection: When 24 V is selected and a 12 V battery is connected, OptiMate 7 12-24 V will immediately warn that a low voltage is detected. Charging will not start. The USER must confirm that the nominal voltage of the connected battery is 24 V before the SAVE mode is activated.CHARGING CURRENT: 10A @ 12V / 5A @ 24V (Ampmatic)USE: Indoor/outdoor (lowest temperature: -40 °F/-40 °C).RECOVERY: Starts from a low voltage of 0.5 V (12 V) and single-phase desulfation recovery.IDEAL FOR: 12 V (3 – 400 Ah) / 24 V (1-200Ah) STD, AGM and GEL batteries.NOW ALSO SUITABLE FOR CALCIUM CALCIUM BATTERIES! special 15 volt charging program INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC-listed), fully sealed.DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable and standard set with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

Y-splitter - SAE to 2 DCLength=12 inch/30 cm2 direct-current inputs of 2,5 mm2-pin SAE connector conforming to the industry standardMaximum cable current: 10 AmpSuitable for use at very low temperatures down to -40 °C/-40 °F, cable remains flexible at temperatures down to “below freezing”.

Ideal 12V battery maintenance for START/STOP & deep cycle applications. The OptiMate 5 recovers batteries from as low as 2 V and then provides charging and maintenance, all automatically. Perfect for months of maintenance of 12 V lead-acid batteries of any size and from 15 Ah to 192 Ah – deep cycle batteries, car batteries (also for EFB batteries – start/stop systems), leisure craft, motorcycles, …CHARGING CURRENT: 4 A (constant current, with temperature compensation)USE: Indoor/outdoor (lowest temperature: -4 °F/-20 °C).RECOVERY: Starts from a low voltage of 2 V and single-phase desulfation recovery.IDEAL FOR: 12 V EFB, STD, AGM and GEL batteries between 15 – 192 AhINPUT CURRENT: Universal (100-240 V 50-60 Hz), fully sealed.DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable and standard set with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

Cable - with DIN connector - cigarette lighterLength : 20/50cm5A maxTM/KETTM-72

This 3300mA portable USB charger with 90° angled BIKE connector can charge up to 2 mobile devices at the same time. This way you charge a combination of your mobile phone, GPS system, camera or tablet via your BMW, TRIUMPH or Victory motorcycle with a standard MOTORCYCLE(DIN) connection.Specifications:- Charge connector (input): 90° standard MOTORCYCLE plug of Ø12mm- Power (input): 12V vehicle system with 12V lead-acid battery or 12.8V lithium battery- Charge connector (output): 2x USB (1x USB-A & 1x USB-C)- Power (output): 3300mA- Style: Fully sealed electronic housing with a blue LED. Unique seal with cap for the USB connection. Any USB cable is sealed when plugged in.Operation: fully automatic:- Vehicle battery protection: USB output shuts off immediately 1 hour after the ignition is switched off or when the battery charge level drops below 12.4V.- Active when the vehicle battery voltage is more than 13.3V.- Short circuit, overheating, overvoltage protectionOperation (Voltage:- USB ON - 13.3V to 18V – unlimited USB output, USB LED on. Supplies power via USB when the vehicle engine charges the battery.- USB 1 HOUR - 12.4V to 13.3V – 1 hour USB output, USB LED on. Enters stand-by mode after 1 hour or at voltage < 12.4V.- STAND-BY MODE – Monitoring the voltage, becomes active again when the vehicle battery voltage is more than 13.3V again.- SWITCHED OFF = 9V

The ultimate pocket-size tester for testing the performance and alternator voltage of batteries fitted in the vehicle, which every maintenance mechanic and technician should have!Easy to use! Place the clamps on the battery or connect to an installed SAE battery cable, and then proceed as follows:1.Check the battery's charge level. A battery with low voltage gives weak starting performance.2.Start the engine. The OptiMate TEST captures and displays the lowest starting voltages (for 20 seconds).3.While the engine is running, check the starting voltage of the alternator and the voltage regulator.TIP: A low charging voltage results in weak battery performance. A charging voltage that is too high causes excessive gassing and ultimately leads to damage to the lead-acid battery. A charging voltage that is too high is FATAL for a LiFePO4 starter battery!•Accuracy via microprocessor.•Easy-to-follow instructions on the back of the tester.•2-pin SAE connector conforming to the industry standard.•Battery clamp set of 40 inch/100 cm.•Fully sealed.A high-quality tester designed by TecMate. 3-year limited replacement warranty.

Socket - SAE - weatherproof - panel mountLength = 15 cm / 6?Front-panel mount, connection at the rear, for panels with a thickness of 1 mm / 0,040? or more.Standard 2-pin SAE connectorMax. cable capacity: 5 AmpUse at very low temperatures -40°C/-40°F; remains flexible at temperatures below freezing.

Adapter kit - 3 pieces - SAE to DC2.5Length of each: 12 inch/30 cm2-pin SAE connector conforming to the industry standard, with built-in sealCoaxial direct-current plug and input of 5,5×2,5 mm Ø with built-in sealMaximum cable current: 10 AmpSuitable for use at very low temperatures down to -40 °C/-40 °F, cable remains flexible at temperatures down to “below freezing”.

Adapter - AUTO socket to BIKE plugConnect your standard USB or GPS charger adapter to a MOTORCYCLE/DIN input such as on BMW, Triumph, Victory motor vehicles, specific Honda Gold Wing motorcycles and John Deere ATVs.•Auto input of 21 mm Ø with internal grooves that keep the connected adapter/connector securely in place.•Power is supplied by a MOTORCYCLE/DIN plug of 12 mm Ø.•Includes cap to protect the plug tip.•Length=12 inch/30 cm•Suitable for use at low temperatures down to -20 °C/-4 °FHigh-quality cable designed by TecMate. 3-year limited warranty.

Adapter - weatherproof SAE cable front panel mounting

CHARGE YOUR 12V – 13.2V BATTERY VIA ANOTHER 12V BATTERY! NO MAINS POWER NEEDED. Ideal for both lead-acid and LFP (LiFePO4) batteries.Charge the battery of your towed motorcycle, quad or speedboat while you are on the road.OptiMATE DC-to-DC draws power from your own vehicle's battery or an external 12V battery to recover, charge and maintain another 12V – 13.2V battery.The highly efficient long-term maintenance mode of the OptiMATE DC-to-DC protects the source battery and only draws power when the battery to be charged needs power. The OptiMATE maintenance mode keeps the battery fully charged, prevents overcharging, extends the service life and improves the battery's performance.OptiMATE DC-to-DC can recover a heavily discharged sulfated battery of even 2 volts.CHARGING AMPS: 2AUSE: indoor / outdoor (lowest temperature: -4 °F / -20 °C).RECOVERY: starts from a low voltage of 2VIDEAL FOR: 12V STD, AGM and GEL batteries and Lithium batteries between 3-96 Ah.INPUT: 12-16 V, 2,7 A maxSTYLE: weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and a 6 ft/180 cm charging cable ending in an SAE connector. Weatherproof battery cable, standard set with battery clamps and fused battery clamp set included.SAFE: no risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year limited replacement warranty.

Y-splitter - SAE to 2x AUTO2 auto inputs with 21 mm Ø and internal locking slots and sealing cap for 2 USB chargers or GPS adapters with car plug.•Length=12 inch/30 cm•2-pin SAE connector conforming to the industry standard•Maximum cable current: 10 Amp•Suitable for use at very low temperatures down to -40 °C/-40 °F, cable remains flexible at temperatures down to “below freezing”.Includes built-in rubber seal for heavy-duty OptiMATE SAE connector. High-quality cable designed by TecMate. 3-year limited warranty.

OptiMate 3 x 4 - 12V 0.8A7-step 12 V 0,8 A battery-saving charger, tester and maintainer with 4 banks The most TRUSTED battery charger in racing in a 4-bank version. The OptiMate 3 x 4, the all-in-one tool for maintaining 4 12V batteries at home, in the garage or in the vehicle storage facility. Diagnosis, recovery, charging, tests and optimal maintenance are carried out automatically. The OptiMate 3 x 4 offers all the user-friendly features of the more than two million OptiMates produced since 1995, but is now lighter and more efficient than ever, and maintains 4 batteries simultaneously and independently of each other. The OptiMate 3 x 4 desulfates batteries and then tests them after charging. The maintenance program delivers only what the battery needs, without ever overcharging or undercharging it. • CHARGING CURRENT: 0,8 A (constant current, per bank)• USE: Indoor/outdoor (lowest temperature: -4 °F/-20 °C).• RECOVERY: Starts from a low voltage of 2 V and two-phase desulfation recovery.• IDEAL FOR: 4 pieces 12 V STD, AGM and GEL battery between 3 – 50 Ah• INPUT CURRENT: Universal (100-240 V 50-60 Hz), high efficiency (CEC-listed), fully sealed.• DESIGN: Weatherproof housing with wall mounts, a 6 ft/180 cm AC cable and 4 charging cables of 6 ft/180 cm ending in an SAE connector. 4 weatherproof battery cables and 4 standard sets with battery clamps included.SAFE: No risk of overcharging. Completely safe for vehicle electronics. Sparks are suppressed. Safe long-term battery maintenance. Automatic shut-off in the event of a short circuit or when the battery is disconnected. 3-year replacement warranty.

Adapter - cigarette lighter to KET - 90cm - TM-68

Socket box - SAE to DC2.5Length: 30cm / 12?Suitable for use at very low temperatures down to -40 °C/-40 °F, cable remains flexible at temperatures down to “below freezing”.

Extension cable - 4.6m - 10A10 Amp extension cable for battery charging cable suitable for use at low temperature with weather- and dirt-resistant SAE connection system.Length=15 ft/460 cm2-pin SAE connector conforming to the industry standardMaximum cable current: 10 AmpSuitable for use at very low temperatures down to -40 °C/-40 °F, cable remains flexible at temperatures down to “below freezing”.Includes built-in rubber seal for heavy-duty OptiMATE SAE connector.High-quality cable designed by TecMate. 3-year limited warranty.

Charge your phone, GPS system, camera or tablet directly via a standard SAE connector connected to the vehicle's 12V system.•Automatic shut-off at low voltage (< 12,4 V) prevents the vehicle battery from fully discharging.•Voltage range: between 12,4 V and 16 V direct current.•12V power via a 2-pin SAE connector conforming to the industry standard.•Actual output current of 5 V 1000 mA.•Protection against short circuit, overheating and overvoltage.•Built-in Apple 1A “handshake” power confirmation.•Included micro/mini USB adapters confirm charging status via cable to other smartphones/GPS systems.High-quality USB product designed by TecMate 3-year limited warranty.