Audio warning
Loud enough to be heard from within the corner zone and set it apart from other background noisesAudio volume can be adjusted (high/low) or simply turned off (on/off)Sounds warning ONLY when motion is detected on both sides of the cornerSynchronized with light flash to reinforce warningVisual warning
Flashes warning ONLY when motion is detected on both sides of the cornerLED lights positioned on the angle, increasing the intensity of the light and optimizing visibilityBeam focused toward areas where it is best seenLens concentrates and increases beam’s intensitySimple installation
Deploys immediately, portable, compact and lightweightIntegrated, recessed magnet mounts easily“snap on” to racking, maintaining a secure, tight fitIntegrated mounting points for mounting the unit to non-magnetic surfacesOptimal installation height is 7 to 9 feet on the uprightSelf-powered
Standard D-cell batteries (included)
Blue light low battery indicator
Battery life depends on usage, but lasts a minimum of 12 monthsPassive infrared motion sensorsDetection zone 20-25 feet in each directionWarning set in ample time for corrective action
Pre-set and ready to use
IMPROVES SAFETY WHEN MOVING LOADSEven your best drivers have problems judging the tilt of their forks when entering or exiting pallets. The risk of pallets mistakenly being pushed or pulled off of a rack or stack is significant. OSHA requires level forks when lifting people on a safety platform. Take control of these problems, by making a fork level indicator part of your driver safety equipment.
REDUCES DAMAGES TO PRODUCTS, PALLETS AND RACKS
The main cause of product, rack and equipment damage is forks tilted at the wrong angle. lf the forks are not level, drivers can spear product from inside or above the pallet opening, bend or push over racking, and splinter pallet s. The Flat Fork will quick ly pay for itself through le ss dama ges.INCREASES PRODUCTIVITY : WORK IS EASIER AND FASTER
Drivers rarely admit it, but they spend a lot of time through trial and error trying to pull and place pallets when werking with elevated leads. Flat Fork makes that work go quickly, and will also show a driver the correct fork angle when traveling with a load or when parking.
INCREASES SAFETY WHEN MOVING LOADS
Even your best drivers have trouble estimating the slope of their forks when moving pallets in and out. The risk of accidentally pushing or pulling pallets off a rack or stack is significant. OSHA requires flat forks when lifting people onto a safety platform. Take control of these problems by making a fork level indicator part of your driver safety equipment.
REDUCES DAMAGE TO PRODUCTS, PALLETS AND RACKS
The leading cause of damage to products, racks and equipment is forks tilted at the wrong angle. If forks are not level, drivers can skewer products from inside or above the pallet opening, bend or knock over racks, and splinter pallets.
INCREASES PRODUCTIVITY: WORK IS EASIER AND FASTER
Drivers rarely admit it, but by trial and error they spend a lot of time pulling and placing pallets when working with elevated lines. Flat Fork makes that work quick and also shows the driver the correct fork angle when driving with a load or when parking.
Our ESQOspeed Radar Ceiling Detection SpeedZoner is an assistance system that
automatically reduces the speed of a vehicle as soon as it goes inside, by means of detecting the ceiling of the building*.
The system actions the speed limiter of the vehicle by selecting the switchable conditional speed.As long as the radar signal is not bounced, the speed limitation is inactive.As soon as the ceiling of the structure is detected the turtle speed will be selected until the machine goes outside again.
* Maximum distance 24 meters from the sensor on top of the head guard to the ceiling.
Specifications :
IP67 Environmental rating
Operating temperature : - 40° to + 65°C (- 40°F to + 149°F)
Supply voltage : 12 or 24 V. DC
Range from : 2 to 24 meter
Sensor operates in Industrial, Scientific, and Medical (ISM) telecommunication band
Frequency modulated continuous (FMCW) radar
Our ESQOspeed Radar Ceiling Detection SpeedZoner is an assistance system that
automatically reduces the speed of a vehicle as soon as it goes inside, by means of detecting the ceiling of the building*.
The system actions the speed limiter of the vehicle by selecting the switchable conditional speed.As long as the radar signal is not bounced, the speed limitation is inactive.As soon as the ceiling of the structure is detected the turtle speed will be selected until the machine goes outside again.
* Maximum distance 24 meters from the sensor on top of the head guard to the ceiling.
Specifications :
IP67 Environmental rating
Operating temperature : - 40° to + 65°C (- 40°F to + 149°F)
Supply voltage : 12 or 24 V. DC
Range from : 2 to 24 meter
Sensor operates in Industrial, Scientific, and Medical (ISM) telecommunication band
Frequency modulated continuous (FMCW) radar
IRIS 860 USB Configuration Cable 2m
To connect to an IRIS sensor allowing sensor setting such as detection distance, range, sensitivity, direction and buzzer volume.
LASER DOT OR LINE HELPS THE DRIVER TO PLACE THE FORK ENDS CORRECTLY INTO THE PALLET
The Forklift Laser Guidance system considerably reduces the risk of damage to pallet goods by projecting a dot or line laser mark thus giving the operator a constant visual reference while stacking- or removing a pallet from the racks at height. This system eliminates the risk of damage by fork points in sacking, carton boxes or any products on pallets. The aligned laser line shines at height of the fork points on the pallet. This allows the driver to position the forks on the right height.
The Forklift Laser Guidance system speeds up the removing of pallets and increases the operational safety in your warehouse. Standard available on class II fork carriage or other at simple request.
Works on 7.5V rechargeable Li-Ion battery pack, laser switches on automatically at vibrations of the forklift or at a certain height.
From the fork back a laser mark is projected on the pallet / product to be moved at the same height as the fork points
Enables the forklift operator to place the forks at the correct height before inserting into the pallet
Simple or dual laser : 1 laser to remove pallets from the rack (aligning on pallet) and 1 laser to insert pallets (aligning on racks)
Battery operated (standard with 2x 7.5VDC Li-Ion battery packs and 220VDC charger)
Hard-wired option (directly connected to tension forklifts, 12-24VDC)
Laser switch on/off according to vibrations, with automatic switching-off at 4min standstill of the forklift
Laser switch on/off according to height, +2m lift height the laser switches on
Laser switch on/off by means of RF remote control by the driver
Heavy-duty and almost indestructible
Immediate decrease of the costs of damage to goods and racks
New but also well-experienced drivers work quicker and safer
Eliminates the guessing of the correct height in the racks
Cold-storage available to -28°C
LASER DOT OR LINE HELPS THE DRIVER TO PLACE THE FORK ENDS CORRECTLY INTO THE PALLET
The Forklift Laser Guidance system considerably reduces the risk of damage to pallet goods by projecting a dot or line laser mark thus giving the operator a constant visual reference while stacking- or removing a pallet from the racks at height. This system eliminates the risk of damage by fork points in sacking, carton boxes or any products on pallets. The aligned laser line shines at height of the fork points on the pallet. This allows the driver to position the forks on the right height.
The Forklift Laser Guidance system speeds up the removing of pallets and increases the operational safety in your warehouse. Standard available on class II fork carriage or other at simple request.
Works on 7.5V rechargeable Li-Ion battery pack, laser switches on automatically at vibrations of the forklift or at a certain height.
From the fork back a laser mark is projected on the pallet / product to be moved at the same height as the fork points
Enables the forklift operator to place the forks at the correct height before inserting into the pallet
Simple or dual laser : 1 laser to remove pallets from the rack (aligning on pallet) and 1 laser to insert pallets (aligning on racks)
Battery operated (standard with 2x 7.5VDC Li-Ion battery packs and 220VDC charger)
Hard-wired option (directly connected to tension forklifts, 12-24VDC)
Laser switch on/off according to vibrations, with automatic switching-off at 4min standstill of the forklift
Laser switch on/off according to height, +2m lift height the laser switches on
Laser switch on/off by means of RF remote control by the driver
Heavy-duty and almost indestructible
Immediate decrease of the costs of damage to goods and racks
New but also well-experienced drivers work quicker and safer
Eliminates the guessing of the correct height in the racks
Cold-storage available to -28°C