Chemical products

CARTRIDGE GUN WITH ADJUSTABLE POWER TRANSMISSIONGun with infinitely adjustable power transmission from 12/1 for the clean application of light, flexible sealant up to 25/1 for easily pumping heavy adhesive, 2K adhesive or a chemical anchor, and everything in between depending on the application. Heavy-duty materials for a long service life and a treated steel drive rod with hanging hook. Ergonomically balanced for optimal relief of fingers and wrists, and a rotating barrel to position the nozzle in the right position. AdvantagesInfinitely variable power setting from 12/1 to 25/1. For light sealants and heavy adhesives in a standard cartridge. Ergonomic lightweight design. Rotatable cartridge holder.Use Cut open the cartridge and screw on the nozzle. Cut off the nozzle according to the required flow rate. Put the cartridge into the holder (piston is at the rear). Turn the adjustment knob to the desired position. The transmission ratio can be read off on the side below the adjustment knob.

The Novatio Multi Sponge is a cleaning product for cleaning and degreasing surfaces.The multi-cleaner removes dirt, grease and deposits from hands, tools and surfaces and keeps the workshop and parts clean. A versatile cleaning agent for maintenance in the workshop and material handling.Multi-cleaner / degreasing spongeFor cleaning surfaces, hands and toolsFor workshop and maintenance

STRUCTURAL REPAIR AND ASSEMBLY OF ALL SYNTHETIC MATERIALSThe Multi Staple Repair is a mechanical repair method for plastics. This strong, structural repair retains the flexibility needed to refit a part. The Multi Staple Repair device heats the "staples" in order to embed them in the material to be repaired. The OEM strength of the base material is left unchanged because no other product is added. Three types of staples ensure a comfortable and effective repair. This Pre Cut Staple has a breaking point so that the staples snap off inside the plastic. The gun of the Multi Staple Repair applies staples straight, or at a 90° angle, for hard-to-reach areas.AdvantagesFor all synthetic materials, so identification is unnecessary. No primers, no cleaners, no preparation. Also ideal for assembly, repair and reinforcement.Use Connect the device to the mains. Set the knob to the desired position: LED lights up green = minimum position for plastic up to 1,5 mm thickness LED lights up yellow = medium position for plastic between 1,5 and 2,5 mm thickness LED lights up red = maximum position for plastic above 2,5 mm thickness Choose the appropriate staple and insert it into the openings provided on the gun (on the head or at 90° depending on the application). Place the head of the staple on the desired spot of the plastic to be repaired and press the start button of the gun. The heat melts the plastic and the staple sinks into the material. Gently turn the gun 5° to embed the staple in the plastic and release the start button. Let the staple cool down before pulling the gun back. Break off the protruding ends.  Place staples until a firm mechanical connection is obtained. Do not use on fibre-reinforced plastics.Technical specifications Supply voltage: 230 V - 50/60 Hz. Max. consumption: 35 W. Dimensions: 165x87x65 mm. Absorption maxima: 160 Ma. 2 fuses of 400 mA. Weight: 1,350 kg. Safety measures: please consult the safety data sheet.

STRUCTURAL REPAIR AND ASSEMBLY OF ALL SYNTHETIC MATERIALSThe Multi Staple Repair is a mechanical repair method for plastics. This strong, structural repair retains the flexibility needed to refit a part. The Multi Staple Repair device heats the "staples" in order to embed them in the material to be repaired. The OEM strength of the base material is left unchanged because no other product is added. Three types of staples ensure a comfortable and effective repair. This Pre Cut Staple has a breaking point so that the staples snap off inside the plastic. The gun of the Multi Staple Repair applies staples straight, or at a 90° angle, for hard-to-reach areas.AdvantagesFor all synthetic materials, so identification is unnecessary. No primers, no cleaners, no preparation. Also ideal for assembly, repair and reinforcement.Use Connect the device to the mains. Set the knob to the desired position: LED lights up green = minimum position for plastic up to 1,5 mm thickness LED lights up yellow = medium position for plastic between 1,5 and 2,5 mm thickness LED lights up red = maximum position for plastic above 2,5 mm thickness Choose the appropriate staple and insert it into the openings provided on the gun (on the head or at 90° depending on the application). Place the head of the staple on the desired spot of the plastic to be repaired and press the start button of the gun. The heat melts the plastic and the staple sinks into the material. Gently turn the gun 5° to embed the staple in the plastic and release the start button. Let the staple cool down before pulling the gun back. Break off the protruding ends.  Place staples until a firm mechanical connection is obtained. Do not use on fibre-reinforced plastics.Technical specifications Supply voltage: 230 V - 50/60 Hz. Max. consumption: 35 W. Dimensions: 165x87x65 mm. Absorption maxima: 160 Ma. 2 fuses of 400 mA. Weight: 1,350 kg. Safety measures: please consult the safety data sheet.

STRUCTURAL REPAIR AND ASSEMBLY OF ALL SYNTHETIC MATERIALSThe Multi Staple Repair is a mechanical repair method for plastics. This strong, structural repair retains the flexibility needed to refit a part. The Multi Staple Repair device heats the "staples" in order to embed them in the material to be repaired. The OEM strength of the base material is left unchanged because no other product is added. Three types of staples ensure a comfortable and effective repair. This Pre Cut Staple has a breaking point so that the staples snap off inside the plastic. The gun of the Multi Staple Repair applies staples straight, or at a 90° angle, for hard-to-reach areas.AdvantagesFor all synthetic materials, so identification is unnecessary. No primers, no cleaners, no preparation. Also ideal for assembly, repair and reinforcement.Use Connect the device to the mains. Set the knob to the desired position: LED lights up green = minimum position for plastic up to 1,5 mm thickness LED lights up yellow = medium position for plastic between 1,5 and 2,5 mm thickness LED lights up red = maximum position for plastic above 2,5 mm thickness Choose the appropriate staple and insert it into the openings provided on the gun (on the head or at 90° depending on the application). Place the head of the staple on the desired spot of the plastic to be repaired and press the start button of the gun. The heat melts the plastic and the staple sinks into the material. Gently turn the gun 5° to embed the staple in the plastic and release the start button. Let the staple cool down before pulling the gun back. Break off the protruding ends.  Place staples until a firm mechanical connection is obtained. Do not use on fibre-reinforced plastics.Technical specifications Supply voltage: 230 V - 50/60 Hz. Max. consumption: 35 W. Dimensions: 165x87x65 mm. Absorption maxima: 160 Ma. 2 fuses of 400 mA. Weight: 1,350 kg. Safety measures: please consult the safety data sheet.

The Novatio Multi Super 5 - Aerosol 400Ml is a professional maintenance/cleaning product from Novatio.This Novatio product is intended for professional maintenance, cleaning or protection in the workshop and industry. Use it according to the instructions on the packaging for the best result.Professional chemical product from NovatioFor maintenance / cleaning / protectionOriginal Novatio part

DISPLACING WATER AND MOISTURE, LUBRICATING, PROTECTING, CLEANING AND LOOSENINGMulti Super 5 provides a high capillary effect and a high creep capacity. It penetrates into the smallest cavity, creating a chemical reaction that loosens rust. Multi Super 5 contains no silicones or graphite.AdvantagesDisplaces water and moisture thanks to its extremely low surface tension. Provides precision lubrication of fine mechanisms. Provides long-lasting protection against water, moisture and corrosion. Cleans both machines and polished surfaces, keeps rubbers soft and supple. Loosens through strong and fast penetration, even in hard-to-reach places.Use Shake before use. Apply. Allow to work in. Allow propellant gases to evaporate if necessary. Technical specifications Specific gravity: 0,811 at 20°C. Flash point: 52°C. Boiling point: 116°C. Solidification point: none down to -62°C. Viscosity at 38°C: 2 mPa.s. Dielectric constant: 33 KV min/215 mm (ASTMD-877). Lubricating capacity: more than 226 kg (Falex step test). Shelf life: 36 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

CLEANER FOR ORGANIC SOILING Cleaner and degreaser for automotive and heavy duty: safe for all common materials from glass and plastic to textile. Apply as foam for good action also on vertical surfaces, and to guarantee surface action. Apply as liquid to penetrate and promote deep action. Simple and safe to use, even on sensitive surfaces, it contains no abrasive and leaves no stains or streaks.AdvantagesFoaming for surface cleaning and liquid for deep action. Without abrasives, so safe on all materials. No rinsing required.Use Foaming effect: fit the trigger with extension tube on the can. Liquid: use the Novatio Pressure Bottle. Spray the surface to be cleaned sparingly and let it act briefly. Remove the loosened dirt with a clean cloth and rub with a clean, dry cloth. Use Novakleen for extreme soiling on textile.Technical specifications Base: cleaning agent, alcohol, additives, perfume and demineralised water. Form: liquid. Colour: transparent. Odour: pleasantly characteristic. pH: 11. Vapour pressure at 20°C (hPa): 43. Water solubility: fully soluble. Relative density at 20°C: 1.001. Volatile organic compound (VOC): 82.252 g/L. Shelf life: dry, cool and frost-free 1L = 24 months. 5L = 36 months. Safety measures: please consult the safety data sheet.

Novatio Multifoam (Aerosol 500ml) - Powerful Cleaning Foam for Various ApplicationsNovatio Multifoam is a versatile and powerful cleaning foam in a handy 500ml aerosol pack. This product is specially developed for thoroughly cleaning various surfaces, including metals, plastic and glass. Thanks to its foaming formula, it penetrates deep through dirt and grease, effortlessly removing stubborn stains and deposits.The aerosol pack ensures easy and targeted application, preventing waste and allowing the product to be used efficiently. Novatio Multifoam is ideal for use in industrial environments, workshops and households where a reliable and effective cleaner is required.Key features:Content: 500ml aerosolPowerful foam for deep cleaningSuitable for various surfacesEasy and targeted applicationRemoves grease, dirt and deposits effectivelyRely on Novatio Multifoam for fast and thorough cleaning that makes your surfaces shine like new again.

FOAMING CLEANER FOR NATURAL SOILING FOR THE FOOD INDUSTRYUniversal, effective foam spray for safely removing natural soiling from all water-resistant surfaces, also vertical. Simple, fast and safe to use, contains no abrasives and has a pleasant fragrance. Causes no scratches, stains or streaks.AdvantagesFresh fragrance. Gentle but effective. Flawless result. 500ml aerosol with 360° spray head.Use Shake before use. Apply and let it act depending on the soiling. Remove with a clean cloth. Rinse with water and wipe dry. Technical specifications Composition: cleaner, alcohol, additives, perfumes, demineralised water. Form: liquid in aerosol, lightly foaming on application. Colour: transparent. Odour: characteristic. NSF registration number: 143423, category A1. Melting point/melting range 0°C: 0. Boiling point/boiling range °C: 78 - 173. pH: 11.1. Vapour pressure/20°C hPa: 8530. Relative density/20°C: 1.001. Auto-ignition °C: 230. Water solubility: fully soluble. Dynamic viscosity mPa.s/20°C: 1. Kinematic viscosity, mm²/s/20°C: 1. Volatile organic compound (VOC) %: 17.14. Volatile organic compound (VOC) g/l: 161.9. Shelf life: 36 months, dry, cool and frost-free.

The Novatio Multifoam FS (aerosol 500ml) is a foam cleaner for vehicles and material handling.This active foam cleaner removes dirt and grease from various surfaces and clings well for thorough cleaning. Ideal for interior and surface cleaning.Active foam cleaner, aerosol 500mlRemoves dirt and grease

FOAMING CLEANER FOR NATURAL SOILING Universal, effective foam spray for safely removing natural soiling from all water-resistant surfaces, also vertical. Simple, fast and safe to use, contains no abrasives and has a pleasant fragrance. Causes no scratches, stains or streaks.AdvantagesFresh fragrance Gentle FlawlessUse Shake before use. Apply and let it act briefly. Wipe dry with a clean lint-free cloth. Finish with a dry cloth.Technical specifications Base: cleaning agent, alcohol, additives, perfume, demineralised water. Form: liquid in aerosol, lightly foaming on application. Colour: transparent. Odour: typical. pH: 10.4. Specific gravity: 0.900 at 20°C. Flash point: none. Shelf life: 36 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

FOAMING CLEANER FOR NATURAL SOILING Universal, effective foam spray for degreasing and cleaning. Simple and safe to use, even on sensitive surfaces. Contains no abrasives and has a pleasant fragrance. Moreover, Multifoam leaves no scratches, stains or streaks on surfaces. AdvantagesPreparation for bonding. Also removes fingerprints. Safe on glass, mirrors, paints, etc.Use Shake well before use. Apply the foam spray. Let it act briefly. Wipe dry with a clean lint-free cloth. Finish with a dry cloth. Technical specifications Product: lightly foaming, liquid in aerosol. Base: cleaning agent, alcohol, additives, perfume, demineralised water. Specific gravity: 0.900 at 20°C. Flash point: none. Shelf life: 36 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

2K EPOXY MORTAR This 2K epoxy mortar is easy to process, to shape and cures shrink-free regardless of the thickness. Suitable for both indoor and outdoor applications and can even be applied vertically up to +/- 4 cm in one layer, so formwork is usually superfluous. Multipox is impact-resistant, water-, chemical- and frost-resistant and offers after curing a dust-free top layer with a high wear resistance. Can be drilled, sawn and ground after curing.Advantages3 x stronger than concrete. For horizontal and vertical repairs, indoors and outdoors. Extreme adhesion to wood, stone, concrete, natural stone, metal,..., without primer. Cures shrink-free in unlimited layer thickness.Use Add the entire contents of the bottle (hardener) to the epoxy mortar and mix well to a homogeneous mass. Apply to a dry, clean and stable substrate at a temperature above +5°C. Working time after mixing: 40 to 60 min., walkable after 24 hours, mechanically loadable after 72 hours and chemically resistant after 7 days. High temperatures accelerate curing, low temperatures slow curing. Clean tools with Novatio Megaclean. Freshly applied mortar covered with plastic film is smooth after curing.Technical specifications Base: glass beads and quartz granulates in epoxy resin and hardener. Solvent-free. Colour: grey. Curing: shrink-free. Solids content: 100%. Adhesion: unbreakable adhesion to most building materials, e.g. stone, concrete, natural stone, wood, metal,...; no adhesion: to most plastics. Max. curing thickness: unlimited. Chemical resistance: resists acids, alkalis, oils, fats, petrols, salts and many solvents, fertilisers, urines,...; resists aggressive gases, steam and sea air. Chlorine resistance: OK. Temperature resistance: -30°C to +60°C permanent; temporary: +90°C. Overpaintable: with the most common lacquers and paints. Application temperature: between +10°C and +25°C. Processing time at 16°C: +/- 50 minutes. Consumption: 1.7 to 2 kg/m² with 1 mm layer thickness. Curing time at 16°C: walkable after 24h. mechanically loadable after 72h. chemically resistant after 7 days. Shelf life: 36 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

AGAINST RUST, MOISTURE, DIRT AND LEAKAGE CURRENTMultispray is fast and effective in contact with rust, tar, grease and water and combines penetrating power, lubrication, protection, cleaning, rust control, moisture displacement and cold shrink, which results in time savings. Multispray contains no silicones and is also safe to use on plastics, paints, ... .AdvantagesSuper-fast reaction. Through cold shrink. Colourless and low-odour. 360° spray.Use Shake well before use. Spray on and allow to work in briefly. Allow propellant gases to evaporate if necessary. Technical specifications Base: mineral oil. Colour: colourless. Odour: characteristic. Water solubility: insoluble. Vapour pressure: 8,53 bar. Boiling point: 187°C – 300°C. Relative density at 20°C: 0,81g. Temperature-resistant: -80°C to +190°C. Dynamic viscosity at 20°C: 1 mPa.s. Kinematic viscosity at 20°C: 1 mPa.s. Shelf life: 100ml: 36 months, dry, cool and frost-free. 600ml: 48 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

AGAINST RUST, MOISTURE, DIRT AND LEAKAGE CURRENTMultispray is fast and effective in contact with rust, tar, grease and water and combines penetrating power, lubrication, protection, cleaning, rust control, moisture displacement and cold shrink, which results in time savings. Multispray contains no silicones and is also safe to use on plastics, paints, ... .AdvantagesSuper-fast reaction. Through cold shrink. Colourless and low-odour. 360° spray.Use Shake well before use. Spray on and allow to work in briefly. Allow propellant gases to evaporate if necessary. Technical specifications Base: mineral oil. Colour: colourless. Odour: characteristic. Water solubility: insoluble. Vapour pressure: 8,53 bar. Boiling point: 187°C – 300°C. Relative density at 20°C: 0,81g. Temperature-resistant: -80°C to +190°C. Dynamic viscosity at 20°C: 1 mPa.s. Kinematic viscosity at 20°C: 1 mPa.s. Shelf life: 100ml: 36 months, dry, cool and frost-free. 600ml: 48 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

AGAINST RUST, MOISTURE, DIRT AND LEAKAGE CURRENTMultispray is fast and effective in contact with rust, tar, grease and water and combines penetrating power, lubrication, protection, cleaning, rust control, moisture displacement and cold shrink, which results in time savings. Multispray contains no silicones and is also safe to use on plastics, paints, ... .AdvantagesSuper-fast reaction. Through cold shrink. Colourless and low-odour. 360° spray.Use Shake well before use. Spray on and allow to work in briefly. Allow propellant gases to evaporate if necessary. Technical specifications Base: mineral oil. Colour: colourless. Odour: characteristic. Water solubility: insoluble. Vapour pressure: 8,53 bar. Boiling point: 187°C – 300°C. Relative density at 20°C: 0,81g. Temperature-resistant: -80°C to +190°C. Dynamic viscosity at 20°C: 1 mPa.s. Kinematic viscosity at 20°C: 1 mPa.s. Shelf life: 100ml: 36 months, dry, cool and frost-free. 600ml: 48 months, dry, cool and frost-free. Safety measures: please consult the safety data sheet.

The Novatio Multistrip is a deburring and cleaning strip for machining and preparing surfaces.With this strip you remove burrs, rust or old coating and clean surfaces for further treatment. Practical tool for repair and surface preparation.Deburring and cleaning stripFor surface preparationProfessional Novatio accessory

THE ULTIMATE FABRIC IMPREGNATION Nano Care Textile prevents dirt from adhering to treated fabrics. It is an invisible yet very effective protection that wraps the fibres in a molecular, intelligent protection. AdvantagesDirt-, oil- and water-repellent. Longer service life and lasting original appearance. Colourless.Use Apply to a clean and dry substrate, from bottom to top in two successive layers, wet on wet. Allow to dry. Remove residue on glass and plastic with a damp cloth. Use only in well-ventilated areas. During application, always wear a mask with filter type A. Nano Care Textile is not a cleaner, nor a stain remover.Technical specifications Boiling point/boiling range: -140°C to +80°C. Vapour pressure at 20°C: 46000 Pa. Relative density at 20°C: 0.790 kg/L. Physical state at 20°C: liquid. Flash point: 11°C. Auto-ignition: 285°C. Water solubility: insoluble. Odour: characteristic. Dynamic viscosity at 20°C: 1 mPa.s. Kinematic viscosity at 20°C: 1 mm²/s. Shelf life: 48 months, dry, cool and frost-free. For specific technical information, please consult the SDS, safety data sheet.

THE ULTIMATE FABRIC IMPREGNATION Nano Care Textile prevents dirt from adhering to treated fabrics. It is an invisible yet very effective protection that wraps the fibres in a molecular, intelligent protection. AdvantagesDirt-, oil- and water-repellent. Longer service life and lasting original appearance. Colourless.Use Apply to a clean and dry substrate, from bottom to top in two successive layers, wet on wet. Allow to dry. Remove residue on glass and plastic with a damp cloth. Use only in well-ventilated areas. During application, always wear a mask with filter type A. Nano Care Textile is not a cleaner, nor a stain remover.Technical specifications Boiling point/boiling range: -140°C to +80°C. Vapour pressure at 20°C: 46000 Pa. Relative density at 20°C: 0.790 kg/L. Physical state at 20°C: liquid. Flash point: 11°C. Auto-ignition: 285°C. Water solubility: insoluble. Odour: characteristic. Dynamic viscosity at 20°C: 1 mPa.s. Kinematic viscosity at 20°C: 1 mm²/s. Shelf life: 36 months, dry, cool and frost-free. For specific technical information, please consult the SDS, safety data sheet.

BREATHABLE PROTECTIVE COATING FOR HEALTHY WALLSDurable, moisture-repellent coating for all absorbent, mineral substrates, such as natural stone, concrete, brick, render, etc.; both indoors and outdoors. Stone Protect is ecological, based on water-borne, mineral nanoparticles; without plastics, solvents or other toxic substances. Thanks to the strong water-repellent effect, a treated surface dries very quickly so that algae and moss cannot germinate, green and black deposits are prevented and dirt is washed away by rain. Masking off windows, panes and other surfaces is unnecessary. Easy to apply with a sprayer, Stone Protect offers more than ten years of protection in a single layer.AdvantagesFor mineral substrates. Invisible and water-repellent.UsePreparation Apply to a clean, dry and receptive substrate. Clean, rinse and dry the substrate if necessary. If a moss remover, acidic or alkaline cleaning agent has been used, rinse the surface thoroughly with water. After sandblasting or another abrasive method, completely remove the dust. The surface must be completely dry. Wait at least 24h after cleaning or a rain shower. Shake Stone Protect well before use and do not dilute. Applying the coating Apply Stone Protect by spraying with the Novatio Pressure Bottle for a controlled, even dosing. For spraying, the HVLP guide value is 4 bar, with a 0.7 - 1mm spray nozzle. This can be adjusted according to the conditions and the experience of the user. For an optimal result, treat the entire substrate with a single non-saturating layer. The yield depends on the absorption capacity and the roughness of the surface, application method, experience and weather conditions. Apply at an ambient temperature between 10°C and 30°C and a R.H. of maximum 85%. Do not apply in rain or frost. Dry in 24 hours, depending on substrate, temperature and quantity applied. Maximum protection after 7 days. Clean surrounding materials before drying with a damp, clean cloth. Immediately after use, clean the tools with clean water. The yield is between 12 and 14 m² per litre (70-80 ml (g)/m²). Wearing gloves and providing good ventilation is recommended. If in doubt about the compatibility with the substrate, first test on a little or non-visible spot. Curing The network of nanoparticles needs 24-48h to cure, bond and activate. The higher the temperature, the faster the curing. During this time it must not come into contact with water. Only after curing is the pearl effect visible. The action is optimal from 7 days after application. Service life The service life of the coating depends on the stability of the substrate, the wear from foot traffic or contact, the chemical load and the degree of air pollution. An actual active service life of more than 10 years is realistic. What can negatively affect the service life or the action: Degradation of the surface. Weak sandstone can flake off, causing the active components to wash away with it. Wear from foot traffic or contact: In places with a lot of foot traffic, the top layer can wear off. Build-up of a layer of dirt. Stone Protect is a surface-active substance. If the surface is covered with dust, pollen or mud, it will temporarily lose its action. Rain and drying restores the action. This is particularly the case on horizontal surfaces, in heavily polluted environments (industry) and after intensive atmospheric pollution (Sahara sand, pollen). Wetting of the surface. Stone Protect is not an impregnation, but functions through electrostatic repulsion of water. If the substrate becomes damp due to water pressure or seepage, this surface effect disappears. Stone Protect does not protect against standing water or water pressure. The nanoparticles form a network that makes the surface water-repellent. If that network is broken by pressure, friction or the use of surfactants, the substrate will absorb water. After it has fully dried, the water-repellent action is automatically restored. Stone Protect offers only limited protection against efflorescence of minerals on brick facades and walls. This is caused by the evaporation of moisture with dissolved metal salts from the stones, mortar or joint mortar, causing those minerals to crystallise on the surface. Because the product does not impregnate and is fully breathable, evaporation and crystallisation will still take place. However, the penetration of moisture through the facade will be greatly reduced, which strongly slows down the effect. There is no effect if the efflorescence is caused by stones or mortar that are too wet, by seeping moisture from the roof or drain, or by rising damp from the ground. Stone Protect is not a cleaner. Stone Protect is not suitable for treating already water-repellent or poorly absorbent surfaces (already treated with a water repellent, polished, non-porous).Technical specifications Base: Silicon dioxide / Silica. Appearance at 20°C: liquid. Colour: colourless. Odour: odourless. Solvent: water. Relative density at 20°C: approx. 1.004 kg/l. pH: 7.5. Viscosity at 20°C: 1 mPa.s Penetration: 5 to 7 mm. Drying time: 24h, low temperatures and high relative humidity slow down drying. Shelf life: at least 24 months, in the closed original packaging, in a cool, dry and frost-free place.

BREATHABLE PROTECTIVE COATING FOR HEALTHY WALLSDurable, moisture-repellent coating for all absorbent, mineral substrates, such as natural stone, concrete, brick, render, etc.; both indoors and outdoors. Stone Protect is ecological, based on water-borne, mineral nanoparticles; without plastics, solvents or other toxic substances. Thanks to the strong water-repellent effect, a treated surface dries very quickly so that algae and mosses do not germinate, green and black deposits are avoided and dirt is washed away by rain. Masking off windows, panes and other surfaces is unnecessary. Easy to apply with a sprayer, Stone Protect offers more than ten years of protection in a single layer.AdvantagesFor mineral substrates. Invisible and water-repellent.UsePreparation  Apply to a clean, dry and receptive substrate. Clean, rinse and dry the substrate, if necessary. If a moss remover, acid or alkaline cleaning agent was used, rinse the surface well with water. After sandblasting or another abrasive method, remove the dust completely. The surface must be completely dry. Wait at least 24h after cleaning or a rain shower. Shake Stone Protect well before use and do not dilute.   Applying the coating Apply Stone Protect by spraying with the Novatio Pressure Bottle for a controlled, even dosage. For spraying, the HVLP reference value is 4 bar, with a 0.7 - 1mm spray opening. This can be adjusted according to the conditions and the experience of the user. For an optimal result, treat the entire substrate with a single non-saturating layer.   The yield depends on the absorption capacity and roughness of the surface, application method, experience and weather conditions. Apply at an ambient temperature between 10°C and 30°C and R.H. of maximum 85%. Do not apply in rain or frost.  Dry in 24 hours, depending on substrate, temperature and applied quantity. Maximum protection after 7 days. Clean surrounding materials before drying with a damp, clean cloth. Immediately after use, clean the tools with clean water. The yield is between 12 and 14 m² per litre (70-80 ml (g)/m²). Wearing gloves and providing good ventilation is recommended. If in doubt about the compatibility with the substrate, first test on a barely or non-visible spot.   Curing The network of nanoparticles needs 24-48h to cure, bond and activate. The higher the temperature, the faster the curing. During this time it must not come into contact with water. Only after curing is the beading effect visible. The action is optimal from 7 days after application.   Service life The service life of the coating depends on the stability of the substrate, weathering from foot traffic or contact, chemical load and the degree of air pollution. A genuine active service life of more than 10 years is realistic.   What can negatively affect the service life or the action: Degradation of the surface. Weak sandstone can flake off, causing the active constituents to be washed away with it. Weathering from foot traffic or contact: In places with a lot of foot traffic, the top layer can wear away. Build-up of a layer of dirt. Stone Protect is a surface-active substance. If the surface is covered with dust, pollen or mud, it will temporarily lose its action. Rain and drying restore the action. This is particularly the case on horizontal surfaces, in heavily polluted environments (industry) and after intensive atmospheric pollution (Saharan sand, pollen). Wetting of the surface. Stone Protect is not an impregnation, but functions through electrostatic repulsion of water. If the substrate becomes damp due to water pressure or seepage, this surface effect ceases. Stone Protect does not protect against standing water or water pressure. The nanoparticles form a network that makes the surface water-repellent. If that network is broken by pressure, friction or the use of surfactants, the substrate will absorb water. After completely drying, the water-repellent action is automatically restored. Stone Protect offers only limited protection against efflorescence of minerals on brick facades and walls. This is caused by the evaporation of moisture with dissolved metal salts from the stones, mortar or pointing mortar, causing those minerals to crystallise on the surface. Because the product does not impregnate and is fully breathable, evaporation and crystallisation will still take place. However, the penetration of moisture through the facade will be greatly reduced, which greatly slows the effect. There is no effect if the efflorescence is caused by overly wet stones or mortar, by seeping moisture from the roof or drain, or by rising damp from the ground. Stone Protect is not a cleaner. Stone Protect is not suitable for treating already water-repellent or poorly absorbent surfaces (already treated with a water repellent, polished, non-porous).Technical specifications Base: Silicon dioxide / Silica. Appearance at 20°C: liquid. Colour: colourless. Odour: odourless. Solvent: water. Relative density at 20°C: approx. 1.004 kg/l. pH: 7.5. Viscosity at 20°C: 1 mPa.s Penetration: 5 to 7 mm. Drying time: 24h, low temperatures and high relative humidity slow the drying. Shelf life: at least 24 months, in closed original packaging, in a cool, dry and frost-free place.

WATER-REPELLENT, DURABLE PROTECTION OF POROUS MATERIALS AND FABRICS Nanocare Protect prevents dirt and moisture from penetrating porous materials and fabrics. It is a durable protection against frost that also slows discolouration from UV rays and inhibits moss and mould formation.  Nanocare Protect improves thermal insulation by 30% and extends the service life of fabrics. Ready to use, without solvents and non-flammable. AdvantagesProtects against oil, grease, dirt, pollution, etc. For indoor and outdoor use. Colourless, odourless and safe. Vapour-permeable.Use Apply to a stable, clean and dry substrate. Clean, rinse and dry the substrate, if necessary.  Apply Nanocare Protect from bottom to top in two successive layers, wet on wet.  Allow to dry. Apply with a brush or using a low-pressure pump fitted with a flat spray. The temperature of the substrate must be at least +5°C. Do not apply in rain or frost. Provide ventilation of the work area and always wear a mask with filter type A during application. Dry in 24 hours, depending on substrate, temperature and applied quantity. Maximum protection after 7 days. Used equipment can be cleaned immediately with water. Remove Nanocare Protect on panes or windows immediately with a damp cloth. With 1 litre of Nanocare Protect you can treat between 2 and 10 m² depending on the porosity of the substrate.    Technical specifications Form: liquid. Odour: weak, characteristic. Melting point/melting range: < 0°C. Boiling point/boiling range: > 100°C. Auto-ignition: none. Explosion hazard: none. Vapour pressure at 20°C: approx. 23 hPa. Density at 20°C: approx. 1.07 g/cm³. Solubility in/miscibility with water: complete. pH value at 20°C: ± 6 (and only apply to substrate with pH value between 6 and 13: so after cleaning and before treatment with Nanocare Protect, rinse well and dry). Shelf life: 36 months, dry, cool and frost-free.

WATER-REPELLENT, DURABLE PROTECTION OF POROUS MATERIALS AND FABRICS Nanocare Protect prevents dirt and moisture from penetrating porous materials and fabrics. It is a durable protection against frost that also slows discolouration from UV rays and inhibits moss and mould formation.  Nanocare Protect improves thermal insulation by 30% and extends the service life of fabrics. Ready to use, without solvents and non-flammable. AdvantagesProtects against oil, grease, dirt, pollution, etc. For indoor and outdoor use. Colourless, odourless and safe. Vapour-permeable.Use Apply to a stable, clean and dry substrate. Clean, rinse and dry the substrate, if necessary.  Apply Nanocare Protect from bottom to top in two successive layers, wet on wet.  Allow to dry. Apply with a brush or using a low-pressure pump fitted with a flat spray. The temperature of the substrate must be at least +5°C. Do not apply in rain or frost. Provide ventilation of the work area and always wear a mask with filter type A during application. Dry in 24 hours, depending on substrate, temperature and applied quantity. Maximum protection after 7 days. Used equipment can be cleaned immediately with water. Remove Nanocare Protect on panes or windows immediately with a damp cloth. With 1 litre of Nanocare Protect you can treat between 2 and 10 m² depending on the porosity of the substrate.    Technical specifications Form: liquid. Odour: weak, characteristic. Melting point/melting range: < 0°C. Boiling point/boiling range: > 100°C. Auto-ignition: none. Explosion hazard: none. Vapour pressure at 20°C: approx. 23 hPa. Density at 20°C: approx. 1.07 g/cm³. Solubility in/miscibility with water: complete. pH value at 20°C: ± 6 (and only apply to substrate with pH value between 6 and 13: so after cleaning and before treatment with Nanocare Protect, rinse well and dry). Shelf life: 36 months, dry, cool and frost-free.